Glassware Dryer - GD-1021

The Model GD1021 Laboratory Glassware Dryer is a high capacity cabinet dryer specifically designed to dry laboratory glassware of all shapes and sizes as well as other items used in the laboratory environment. Adjustable shelves allow several loads of glassware to be dried at the same time.

Adobe AcrobatGlassware Dryer

 

Model
Chamber Size

Exterior Overal Size

Heat

Type

W

H

D

W

D

H

GD-1021S
30"
26"
54"
36"
32"
80"
Steam
GD-1021E
30"
26"
54"
36"
32"
80"
Electric

*Note: Dimensions are maximum chamber opening sizes. Actual load size must be smaller to allow for clearances.  Custom chamber sizes can be provided as required. 

Automatic Temperature Regulation

  • All models shall incorporate analog temperature controls adjustable from the front panel.
  • Steam Heat
    • Heating system shall consist of a commercial steam to air heat exchanger, complete with valves, strainer, condensate trap and all other necessary trim. Unit shall be easily removable for cleaning or repair.
  • Electric Heat
    • Heating system shall consist of Finned Strip-type heating elements with contactor, short circuit and over temperature protection and all other electrical appliances necessary in accordance with NEC and UL specifications.

Insulated Exterior

  • The exterior of the machine shall be fully insulated with 2" of rigid insulation covered by a Stainless Steel jacket for protection. This insulation shall be an integral part of the machine, designed to limit radiation loss to the surrounding air.

Machine Operation

  • All interior and exterior parts shall be of Type 304 Stainless Steel or other Non-Corrosive materials.
  • Electrical assemblies, piping assemblies and mechanical apparatus shall be designed for, and be appropriate for use in, a high temperature sanitary wash-down environment. All components shall be selected for their ability to perform for long periods of time in the adverse and high production environment of the laboratory washroom. Each purchased part and each engineered part and sub-assembly shall be scrutinized and all specific design decisions shall be made in the light of these basic criteria.
  • All purchased components shall be un-modified, off-of-the-shelf items available to the owner in his locality, should he need them.
  • Original manufacturers' part numbers and descriptive information for all purchased parts shall be made an integral part of the service manual information provided at time of installation, and every effort shall be made throughout the life of the machine to assist the owner in acquiring any parts needed.
  • The door of the dryer shall be of double-walled stainless steel construction, 1" thick, and filled with insulation.
  • Temperature shall be controlled up to 240 degrees F.

 

MATERIALS OF CONSTRUCTION

Item

Material

Frame

Carbon steel, enameled
Door Pannels
16 gauge, 304 SS - #3 finish
Side and Top Panels
20 gauge, 304 SS - #3 finish
External Steam Piping
schedule 40 black iron

Utility Requirements

Item
Item

Material

Electric
Steam

Electrical

 110V, 1ph, 60hz, 15 Amps 3ph, 60hz, 8 HP
5.97 KW
Steam Min. 1/2 FPT
30-50 PSI
100#/Hr Max Flow		 N/A
Condensate 1/2 FPT N/A
Exhaust

4" Dia.

100 SCFM

4" Dia.

100 SCFM

Notes to Utilities

  • A disconnect switch shall be installed by others than SMC in accordance with all NEC and local electrical codes.
  • Condensate shall be connected by others than SMC to a non-pressurized gravity main. The maximum condensate lift shall not exceed 15'.
  • Steam pressure shall not exceed 60 psi. Factory shall be consulted for steam pressures below 30 psi dynamic.
  • Exhaust connection shall be made by others than Geneva Scientific using non-corroding materials, and all ductwork shall be sealed and pitched towards the machine. 

Additional Engineering Information 

Item

Material

Shipping Weight

 800 lbs
Dynamic Weight as Installed 650 lbs
Heat Radiation 500 Btu

©2006 GENEVA SCIENTIFIC ALL RIGHTS RESERVED | Internet Marketing by Atlantic BT